#Iuweshare usb flash drive data recovery install
#Iuweshare usb flash drive data recovery software

just a few years back, there was a big spread between the different recovery programs and what they could recover.

#Iuweshare usb flash drive data recovery install

I install each GOTD Recovery program and test it against a common disk that has files that the OS cannot find, but most recovery programs can.

#Iuweshare usb flash drive data recovery software

Regardless of any immediate need, it is always a good idea to have good recovery programs such as IUWEshare USB Flash Drive Data Recovery software installed, just in case you ever need it. As a last resort, there are companies that do the delicate diagnostics to recover data. I work in electronics so attempting this type of recovery is not as much of a scare for me as it is for someone that does not do that type of diagnostics. I started in electronics many years ago, so I am sure that I am reaching the end. As more media become memory chip based, I probably will not have another chance for a long time if at all. The last one I had fail where I could attempt this type of recovery was just over 3 years ago, and the last one before that was 5 more years. Hard drives are getting much more reliable as well. The first two were SCSI drives, from a long time ago, and I was not able to recover anything. Each one was way beyond their projected life, and HD Sentinel warned of their impending death for the last two (didn't have it before). So far, I have had success with 3 of the 5 drives. Over all the many years, I have only had this happen five times. Still, it is a challenge for me, so I still go through the duplicate drive recovery method just to see if it is possible.

In those rare occasions that a drive of any type fails, it becomes a piece of hardware that I cannot trust to ever use again (a throwaway item). I always do multiple types of backups, so I have never needed to rescue my own data. Nowadays, hard drives, external drives, backup drives, are all very inexpensive compared to how they once were.

Then if after all other types of recovery fails, at least I have a drive that the media can be placed into for another attempt. That way if one of the drives ever fail, I immediately remove it from the system, and copy all the data off of the other so that it can be re-formatted to be as close as possible to how I initially received it. When I purchase a new drive of any type, I purchase two of the exact model, hoping to get the same matching electronics versions off of of the assembly line. Even that can be difficult with something like an IOMAGIC drive because of the difficulty even getting into them to do any diagnostic. If you get that solved, that may be all you need. It could be loose wire, solder joint, bad switch, bad connector, or any other reason that the electrical power is not reaching the hardware electronics. First, see if you can get the power problem solved. You can see from that dilemma, that determining why the power is not working may be a better approach. It makes it all very difficult in some cases, and can be very expensive to actually recover the data. Manufacturers often change chip suppliers midstream, and those chips can be programmed differently. Also, the electronics hardware of the two drives often have to have the exact same model numbers of the individual components, otherwise they might not be programmed to work the same way as to how they locate data on the media. If the new drive's electronics work the same as the original drive, then the data can be accessed, as long as the media itself is still readable. Here is the concept regardless of what media the data is stored on. Still, it might be possible if the data is that valuable. Of course that is changing with more memory chips being used for storage. I know that is way more than the average person is willing to face, but technically it could be possible.įor standard (magnetic platter) hard drives, this type of recovery has been used by the high-end recovery shops. It might be possible to separate the media (memory chips) and transfer them to another matching drive. That can be difficult for an IOMAGIC drive because everything tends to be on one circuit board. Otherwise, if the electronics does not work, or the electronics do not have electrical power, then the drive has to be disassembled, the media taken out, and then placed into an exact duplicate of the drive it came out of. A drive has to 'Power up' in order for the electronics to work, which is needed by any program that needs to access the data.